• Orange with KTM logo
• 50 mm wide & 99 m long

• Protects the brake pedal from bending by branches

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Teeth made of high-strength steel, for an extra long service life
• Aluminum center section, reduces unsprung masses
• Permanently joined together with high-strength rivets
• At least three times longer service life than other aluminum rear sprockets
• 50 % lighter than steel rear sprockets
• Longer service life of the entire drivetrain kit

• CNC milled from high-strength aluminum
• Elegant anodised surface

• CNC milled from high-strength aluminum
• Elegant anodised surface

• Uncompromising race look
• CNC milled from high-strength aluminum
• Resistant to the toughest stresses and strains

• Race look

• Protects the footpegs from damage during a potential fall

• Coated neoprene ring
• Simply pulled over the grips

• Developed according to the requirements of our factory drivers
• Less stress when riding
• Objective: comfort AND safety
• Ergonomic contour adapted to the shape of the hand for maximum comfort
• Half waffle grip
• For a secure grip
• Three areas for the metal wire locking
• Version: medium

• Developed according to the requirements of our factory drivers
• Less stress when riding
• Objective: comfort AND safety
• Ergonomic contour adapted to the shape of the hand for maximum comfort
• Half waffle grip
• For a secure grip
• Three areas for the metal wire locking
• Version: soft

• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Prevents the hand grips from chafing in the event of a fall

• CNC milled from high-strength aluminum
• Easy to mount
• Optimal protection against stone impact
• Prevents damage to the engine housing in the event of chain cracks
• No stones drawn in between chain and engine housing (gentle on the material)

• CNC milled from high-strength aluminum
• Not lockable
• Extremely fast and keyless refueling

• Prevents dust and dirt from entering the tank when the fuel tank cap is opened
• Filter is attached directly to the tank opening
• Fits all 3/4 fuel tank caps

• For tank and carburetor bleeding
• Gasoline resistant
• Can only be used for bleeding purposes
• Cannot be used as a connection between tank and carburetor!

• Tool for lifting the motorcycle
• Secure stand for your bike

• Secure stand for your bike

• Made especially for 50 / 65 / 85 models
• Aluminum construction with a non-slip pad.
• The top is wedge shaped and solid so the bike doesn't slide around when washing.

• Stabilises the motorcycle during transport
• After transport, the tool serves as a perfect plug-in stand!

• Testing, charging and keeping batteries fresh
• Fully automatic and economical battery charging by means of programmed charge characteristic
• Short-circuit protection
• Reverse polarity protection

• Can be used for several types of batteries (Pb, LiFePo4)
• Charging with a specific power control program
• Trickle charge during diagnostic or flashing the vehicle
• Recovery mode for low battery voltage (BMS, battery management system)
• Optimizes battery performance and service life
• Including power supply cable type EU

• The Bead Buddy acts as your third hand when fitting tires
• Holds the tire in the tire bed, thereby making tire fitting much easier
• Simply hook it into the spokes and away you go Particularly recommended for tire fitting with mousse.

• Easy handling and operation
• More safety
• Less wear on the cord
• Made of high quality material
• Cable not included

• 3 x short version 51012092100
• 3 x long version 51012093100

• Use this to remove the dirt from your last mud battle with ease!
• A motorcycle grip rubber (not included) can be fitted to the grip.

• Makes setting the sag significantly simpler.
• Folding version for easy stowing in the tool box.

• Contains all the most-used bolts and small parts for current Offroad models
• 30 % saving compared with purchasing individual parts

- Push-on spoke wrenches in sizes 5.65 and 6.95 mm
- Push-on ratchet ¼"
- Ratchet attachments: 6, 8, 10 mm socket wrench, 15 Torx

• Protects the intake system against water and dirt when cleaning the air filter box

• Keeps water out of the silencer during cleaning.
• For inner-diameter of 22-42 mm

• Comfortable and easy to use
• Fits all standard valves. Pressure display in bar or psi
• Integrated pressure release valve for accurate pressure adjustment
• Disengageable display and work area lighting
• Energy-saving function with automatic cut-off
• Maximum measuring pressure: 11 bar

• Highest quality workmanship
• Including straps

• It withstands a load of 180 kg.
• The total length is approx.200 cm, folded approx.100 cm.

• Practical help when loading the bike or jacking up with the rear wheel lifting device

• Perfect for all on the move
• Exceptionally robust

• Can be used with XACT/ XPLOR forks and shocks
• Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

• Prevents dirty grips

• This mat is already mandatory for many races
• The special material mix absorbs overflowing fuel
• The mat also facilitates the retrieval of tools, screws and other small parts during service work
• Complies with FIM regulations
• Rubberised back

• This mat is already mandatory for many races
• Complies with FIM regulations
• The special material mix absorbs overflowing fuel
• The mat also facilitates the retrieval of tools, screws and other small parts during service work
• Rubberised back

• Size: 170 cm x 100 cm

• Enables secure fastening of the machine
• Protects handlebar and tank from scratches
• Made from durable ballistic nylon
• Load capacity of 280 kg
• With handlebar loops
• With rubberised hooks and carabiner on belt ends

• Provides optimum protection

• Provides optimum protection

• Made from high-tensile, durable steel
• Highest quality workmanship

• Double locking mechanism
• Locking cylinder with optimum protection against any attempts at manipulation
• Two keys supplied as standard
• Includes rotating PVC cover that protects the cylinder lock from dirt

• Made of robust material
• Pre-cut stickers

• Elegant look

• Anodised valve caps

• 220 Volt
• For all WP-shocks
• Two 3 litre tanks
• Fill two different shocks at the same time
• Programmable filling cycle time
• Two filling presets
• Intuitive control via a 4.3" LCD screen
• Low oil warning
• Vacuum 42L/min
• Max. vacuum -0,98 bar
• Adjustable pressure 1,5-3 bar
• Incl. 2 WP-adapters